- 面议
起订量：
真空泵
- 型号
详细信息
精益设计只为成就更高品质10年来，这一方针指引剑门泵业产品质量上了一个又一个新台阶。四川省、四川省产品、质量信誉AA企业、船用产品型式认可、法国BV认证、中华人民共和国进出口企业资格、国家消防产品生产许可证、中国石油天燃气集团入网证、四川省免检产品、康明斯免检产品等殊荣是剑门牌水泵高品质有力的佐证，顾客满意度85%是客户对剑门人无私的肯定。
一大批工艺技术及结构改进项目，如机器造型工艺、柔性密封技术、粉末静电涂敷技术、叶轮CFD设计、新型泵盖设计、新型轴承体设计等得到成功运用，剑门水泵也籍此在产品可靠、节能、美观方面处于行业。
建立了包括模具制造、铸锻件生产、理化检验、机械加工、装配、测试等在内的完整的制造体系。有各类主要设备400余台(套)，其中包括大型立车、铣床、龙门刨、抛丸机、数控机床、新型造型机、1.5吨中频炉、5吨树脂砂再生处理系统、3吨冲天炉、600吨液压机、自动测试台架、大型清洗机等重点设备达40余台(套)
■ 概述
●IS型系列单级单吸清水离心 泵是按照国际ISO2858标准设计的，技术指标均达到和超过国家标准，具有效率高，结构合理，使用可靠、“三化”程度高的特点，是工厂、矿山、城市给排水及农田灌溉的理想产品。我公司在IS泵的基础上 ，增加冷却系统，生产出ISR热水泵;改变材质生产出用于化工、食品、医药等行业的ISF化工泵;改变结构生产出ISW污水泵和无堵塞泵;采用机械密封生产出ISJ机封泵。
●IS、ISR、ISF、ISW泵的吸入压力不得大于0.3MPa(即3kg/cm2)(若用户对吸入压力、温度、介质等有特殊要求可与本公司协商确定)
■ Summary
●The IS series pump has been designed according to ISO 2858.This high efficiency, good structure, high reliability pumps has been developed for works, mines, cities and farms. Improving IS series pump, we also manufacture ISR hot water pump, ISF chemistry pump, ISW sewage pump and ISJ mechanical seal pump.
■ 型号说明
IS(ISR、ISF、ISW、ISJ)- 65 - 40 - 250- A、B
■结构 Sectional Drawing
1.泵体 2.泵盖 3.叶轮 4.轴 5.密封环 6.叶轮螺母 7.止动垫圈 8.轴套
9.填料压盖 10.填料环 11.填料 12.悬架轴承部件(ISJ轴封用机械密封)
■ 结构说明
●IS型泵是根据国际标准ISO2808规定的性能、尺寸设计的，主要由泵体(1)、叶轮(2)、轴套(3)、及托架 (12) 、轴(13)、泵盖(14)等组成。
●IS型泵的泵体和泵盖部分是从叶轮背面处剖分的，即通常所说的后开门结构形式。其优点是检修方便，检修时不动泵体、吸入管路、排出管路，只需移动电机，即可退出转子部件进行检修。
●泵的壳体(即泵体和泵盖)组成泵的工作室。叶轮、轴和滚动轴承等为泵的转子。悬架轴承部件支承着泵的转子部分，滚动轴承承受泵的径向力和轴向力。
●为了平衡泵的轴向力，大多数泵在叶轮后盖板上设有平衡孔;由于有些泵的轴向力不大，叶轮背面未设平衡孔。
●泵采用机械密封，并可根据不同条件，采用不同结构和材料的密封。
●为避免轴磨损，在轴通过密封腔的部位装有轴套保护。轴套与轴之间有O型密封圈，以防沿着配合表面进气或漏水。
●泵的传动方式是通过爪型联轴器与电动机直联的。泵的旋转方向，从驱动端看，为顺时针方向旋转。
■ Explanation of Structure
●The IS series pump has been designed with performance and size of ISO 2858. Its main part include casing (1), Impeller (2), haft sleeve (3), Frame (12) , shaft (13),casing cover (14) ,etc. The IS series pump is divided into casing and casing cover at back of impeller, so you could dismantle it very easy.
●The pump's working house is made from casing and casing cover. Its rotator set is made from impeller, shaft and bearings. The rotator of the pump is propped by bearing bracket. The balance role has been designed in back cover of impeller to balance the axial force of the pump. But, when the pump's axial force is relatively small, we don't design balance role.
●The IS series pump’s shaft seal is mechanical seal. We may supply you with various material and structure mechanical seal to meet you all demands.
●The sleeve is designed round the shaft at packing house to protect the shaft. 'O' type seal ring is designed between the sleeve and the shaft to prevent leakage of air and water.
●The claw type coupling is designed between the pump and the electrical machine to drive the pump. Looking from the back of the electrical machine, the pump's rotation direction is clockwise.
