揭阳冷却水塔圆形*的
揭阳冷却水塔圆形*的
揭阳冷却水塔圆形*的
揭阳冷却水塔圆形*的
揭阳冷却水塔圆形*的

CT-175T揭阳冷却水塔圆形*的

参考价: 面议

具体成交价以合同协议为准
2016-12-22 15:14:13
251
产品属性
关闭
广东菱峰冷却塔制造有限公司

广东菱峰冷却塔制造有限公司

免费会员
收藏

组合推荐相似产品

产品简介

圆形逆流冷却塔

详细介绍

揭阳冷却水塔圆形的,榕城冷却水塔圆形的,普宁冷却水塔圆形的

东莞市菱电实业投资有限公司
地址:广东省东莞市大朗镇新玛莲马坑新区2号
:    

冷却塔运行保养方法:
    1:进行前,需将冷却塔水盘和塔体内部杂物清除干净;
    2:传动皮带过紧会导致轴承损坏,过松则会导致皮带打滑发热从而降低耐久度;
    3:冷却塔经过一个星期运转后,必须重新更换循环水,以便清除管路中之尘垢杂物;
    4:冷却塔经过5-6天的运转,若皮带出现松弛的话,需重新调整皮带的松紧度;
    5:冷却塔若*停机时,应松开皮带,使之避免承受不必要的张力;
    6:冬季、冷却塔若*停机时,必须将管路之循环水全部排除,避免冬季结冰造成龟裂,冷水盘之排水管随时打开,以便雨水、溶雪能够流出;
    7:日常运行时,应留意冷却塔底盘中的水位。冷水盘水位需保持一定高度;
    8:冷却塔在停机一段时间后重新运转,此时必须检查马达绝缘是否正常。

揭阳冷却水塔圆形的,榕城冷却水塔圆形的,普宁冷却水塔圆形的

冷却塔填料清洁办法(一):
    1、人工清扫冷却塔内脱落的垢渣;
    2、用高压水枪反复冲刷填料,铲除清洁下的污泥水垢等;
    3、用50℃摆布热水将TNB安全除垢剂溶解后用冲刷泵反复冲刷填料,直至水垢冲刷洁净,一起参加灭藻剂,*杀灭生物藻类及;
    4、承认体系遍地悉数清洁洁净后,排去污水;
    5、用清水冲刷填料及塔身表里;
    6、恢复体系遍地,补水即可运用;
    7、悉数恢复后,请需要清洁方管理人员检验;
    8、撤离己方物品,清扫现场清洁;
    9、工期:依据实际情况定。
冷却塔填料清洁办法(二):
    1、暂时用塑料布建立一个大水池;
    2、将清洁剂参加清水中;
    3、将填料从冷却塔中拆下来放入药池中浸泡;冷却塔厂
    4、将浸泡洁净的填料用清水冲刷洁净后装回冷却塔;
    5、用粘有药剂的布放在冷却塔补水器上,将补水器口浸泡疏通;
    6、用同样的办法将冷却塔底盘水垢进行铲除洁净;
    7、用清水冲刷填料及塔身表里;
    8、恢复体系遍地,补水即可运用;
    9、工期:依据实际情况定。

Cooling tower packing cleaning method (1):
1, manual cleaning slag cooling tower off;
2, repeatedly washed with water cannons to eradicate the filler, clean sludge scale etc.;
3, in 50 degrees of hot water at the mercy of the TNB security remover dissolved in flushing pump washed repeatedly until the scale filler, rinse clean, join the algaecide, compley kill algae and biological;
4, recognize the system clean and clean everywhere, drained sewage;
5, wash with water and packing inside and outside the tower;
6, restore the system everywhere, replenishment can be used;
7, after full restoration, please clean the party manager inspection;
8, one's own evacuation items, cleaning cleaning;
9, duration: Based on the actual situation.
Cooling tower packing cleaning method (two):
1, the temporary use of plastic sheeting to build a large pool;
2, will clean agent to participate in clear water;
3, the packing from the cooling tower removed into the drug tank soak; cooling tower factory
4, soak clean packing with clean water after cleaning back to the cooling tower;
5, with adhesive cloth on the cooling tower water supply device, will water supply device mouth soak dredge;
6, in the same way the cooling tower chassis to eradicate clean scale;
7, wash with water and packing inside and outside the tower;
8, restore the system everywhere, replenishment can be used;
9, duration: Based on the actual situation.

,榕城冷却水塔圆形的,普宁冷却水塔圆形的

东莞市菱电实业投资有限公司
地址:广东省东莞市大朗镇新玛莲马坑新区2号
:    

上一篇:耐腐蚀冷却塔的安装的相关事项说明 下一篇:圆形耐腐蚀冷却塔安装中不可忽视的一些事项
热线电话 在线询价
提示

请选择您要拨打的电话: