QCS - 3汽车内饰材料阻燃性能试验机

五、设计标准
Five, design standards
GB8410-2006
GB8410-2006
FMVSS 571.302等标准规定的模拟燃烧性能安全试验项目
FMVSS 571.302 standard requirements for the simulation of the combustion performance safety test project
DIN7520《汽车内饰材料的燃烧特性》
DIN7520 "combustion characteristics of automotive interior materials"
TL1010汽车内饰材料燃烧特性
Combustion characteristics of TL1010 automotive interior materials
符合标准：GM6090M、DIN75200、GM9070P、FMVSS 302、JIS D 1201、JASO M403 、ISO 3795、ASTM D5132、QB／T 2729-2005
Meet the standards: GM6090M, DIN75200, GM9070P, FMVSS 302, D JIS 1201, M403 ISO, ASTM 3795, D5132 QB, T / 2729-2005 JASO
二、汽车内饰材料阻燃性能试验机工作条件及主要技术指标
Two, working conditions and the main technical indicators
1.环境温度：-5℃-30 ℃
1 ambient temperature: -30 C -5 C
2.相对湿度：≤ 85%
2 relative humidity: less than 85%
3.供电电压：220V+ 10%、50HZ,功率：100W
3 power supply voltage: 220V+ 10%, 50HZ, power: 100W
4.气源：液化石油气
4 gas source: liquefied petroleum gas
5.秒表精度不低于0.5s
5 stopwatch accuracy is not less than 0.5s
6.本生灯（即燃烧器）对试样施加火焰15s
6 this lamp (i.e. burner) is applied to the test specimen with a flame 15s
7.本生灯管内径9.5mm+ 0.1mmm，长约100mm
7 the diameter of the tube is 0.1mmm 9.5mm+, which is about 100mm
8.试验倾角：本生灯90°垂直对着水平放置的样品燃烧
8 test angle: the 90 degree of the lamp is placed in the vertical to the horizontal.
9.火焰高度：20mm± 2mm 到100mm±2mm可调(一般调为38mm)
9 flame height: 20mm + 2mm to 100mm + 2mm adjustable (generally adjustable to 38mm)
10.施焰时间：0-999.9s±0.1s可调（一般选择为15s)
10 Shi Yan time: 0-999.9s + 0.1s adjustable (generally selected as 15s)
11.续燃时间：0-999.9s±0.1s，观察火焰达到*标线后手动开始、手动暂停
11 afterflame time: 0-999.9s + 0.1s, observe the flame to the first line after the manual start, manual pause
12.燃烧气体：液化石油气或煤气
12 burning gas: liquefied petroleum gas or gas
13.温度范围：0～200℃（显示测试状态下工作室内部温度）
13 temperature range: 0 to 200 degrees C (display the test status of the studio interior temperature)
一、简介
Brief introduction
QCS-3型试验装置，根据国家标准GB8410-2006《汽车内饰材料的燃烧特性》的规定技术要求而设计的，同时符合美国汽车安全技术法规FMVSS 571.302等标准规定的模拟燃烧性能安全试验项目、德标DIN7520《汽车内饰材料的燃烧特性》及TL1010《汽车内饰材料燃烧特性》的相关要求，用于鉴别轿车、多用乘客车、载货汽车和客车内饰材料水平燃烧特性。
QCS-3 type combustion test device of automotive interior materials, according to the national standard GB8410-2006 "automotive interior materials" the combustion characteristics of the technical requirements and design, at the same time with the American vehicle safety technical regulations FMVSS 571.302 standard combustion simulation performance security testing project, German standard DIN7520 "automotive interior materials" and "auto combustion characteristics TL1010 the combustion characteristics of" interior materials of the relevant requirements, for the identification of cars, multipurpose passenger car, truck and bus interior material level of combustion characteristics.
三、组成
Three, equipment composition
1.设备分控制部分与通风橱一体、燃烧室内置。
1 the equipment control section and one combustion chamber, built-in ventilation cabinet.
2.点火自动控制系统
2 ignition automatic control system
3.试验过程：试验程序自动控制
3 test procedure: test program automatic control
4.自动进排气系统（燃气自动开启、自动关闭）
4 automatic air intake and exhaust system (gas automatic start, automatic shutdown)
5.计时系统：燃烧计时器、余焰计时器
5 timing system: combustion timer, timer
6.U型支架：上支架有6个销孔，下支架对应有6个销子，并布有线径为0.25mm及间距为25mm的耐热金属支撑线
6.U support: support with 6 pin holes, the lower bracket corresponding to 6 pins, and cloth cable diameter is 0.25mm and the distance to 25mm heat-resistant metal support line
7.试验支架第三标线距第二标线距离为154mm
7 test support third from the second distance 154mm marking marking
8.耐热金属丝槽 0.5mm X 0.5mm 间距 25mm
8 heat resistant metal wire groove X 0.5mm 0.5mm spacing 25mm
9.金属丝长度大于110mm,每25mm有7~8个光圆齿
9 metal wire length is greater than 110mm, each 7~8 has 25mm light round tooth
10.温度数显，测量范围0-200℃
10 temperature digital display, measuring range 0-200
11.火焰标尺精度：0.1mm
11 flame scale precision: 0.1mm
12.设备外形尺寸：长 * 宽 * 高 1300 * 650 * 1200（钢板静电喷涂材质）
12 equipment size: long * wide * 650 * 1300 * 1200 * (steel electrostatic spraying material)
四、试样尺寸：长356mm、宽100mm、厚≤ 13mm
Four, sample size: length 356mm, width 100mm, thickness of less than 13mm